October 25, 2018 posted by

1 Oct Last previous edition approved in as A – 07´1. DOI: /A 2 For referenced ASTM standards, visit the ASTM website. ASTM A Standard Specification for Tool Steel. On May 9, / ASTM, Standards · ASTM A Standard Specification for Tool Steel Alloy · Next Post. Introduction. S7 tool steel is a shock resisting tool steel with excellent toughness and high strength, along with medium wear resistance. It has maximum shock.

Author: Kagarg Datilar
Country: Panama
Language: English (Spanish)
Genre: Love
Published (Last): 18 April 2005
Pages: 169
PDF File Size: 19.84 Mb
ePub File Size: 4.97 Mb
ISBN: 427-7-18040-822-4
Downloads: 26268
Price: Free* [*Free Regsitration Required]
Uploader: Moll

L6 Tool Steel 1. Sales Manager for European, African, Asia market: S7 tool steel is normally tempered one and one-half hours to two hours for each inch of greatest crosssection. astm a681

H13 Zstm Steel 1. Chemical composition, hardness, macrostructure and decarburization of astm a681 material shall conform to the requirements in accordance to the referenced ASTM documents itemized herein.

ASTM A – 08 Standard Specification for Tool Steels Alloy

Fushun Special Steel Co. H13 Tool Steel is chromium hot-work tool steels. AISI P20 Steel Plate Material is a versatile, low-alloy tool steel astm a681 is ast by good toughness at moderate strength levels. It is informational only and not an official part of the standard; the full text of the standard itself astm a681 be referred to for its use and application. Sales Manager for American, Oceanian, Asian market: D2 Tool Steel 1.


D3 Cold Astm a681 Steel 1. Quenching in oil gives an increased risk for dimensional changes and cracks. The values given in parentheses are mathematical conversions to Astm a681 units that are provided for atsm only and are not considered standard.

This is not an anneal, and after the forging is cold, it must be properly annealed. Referenced Documents purchase separately Astm a681 documents listed below are referenced within the subject standard astm a681 are not provided as part of the standard.

ASTM A – 08() Standard Specification for Tool Steels Alloy

Astm a681 steel supplies NAK80 mold steel for high end plastic mold steel. Back to Top Workability Forging: It has maximum shock resistance and high compression strength, which gives it good deformation resistance in use, while retaining good toughness.

Reanneal or temper F C for 4 hours after welding. Founded inFuShun covers an astm a681 of square meters, annual sales volume of tons. Some equivalent steel is 1. A2 Tool Steel 1. O1 Tool Steel 1.

Contact Lists General Manager: NAK80 steel is a precipitation or age-hardened mold astm a681 with a uniform through hardness of approximately 40 HRC. Cool to F 65C after welding.


P20 Steel Plate 1. This specification covers the chemical, mechanical, and physical requirements for available wrought alloy astm a681 steel products. It is recommended for both hot and cold shock applications such as rivet sets, chisels, punches, moil points, hot headers and gripper dies.

About Us Founded inFuShun covers an area of square astm a681, annual sales volume of tons. The selection of astm a681 material for a particular application will depend upon design, service conditions, and desired properties.

Miss Summer summer fushunspecialsteel.

ASTM A681 Grade S1 annealed

D3 cold work steel has very high wear resistance against abrasive and adhesive wear. The tempering temperature astm a681 according to astm a681 intended use. This abstract is a brief summary of the referenced standard. AISI S7 steel has exceptional impact properties plus the highest hardenability of shock resisting grades of tool steel.

It can be quenched in air, exhibiting minimal distortion on hardening.